Furniture hinges (hinges) - one of the most important elements of hardware, which determines the comfort, reliability and durability of your furniture. However, even dribnіні помилки під hour of installation zavіс can negatively affect their work, call for quick wear, noise, nervous nіvnomіrnomіrnoe prilagannіya doors and even poshkodzhennіya facades. You can buy furniture curtains on the website https://deks.ua/catalog/mebleva-furnitura/zavisi-petli/zavisi
We will review seven of the most widespread errors in the installation of furniture zavis, explain why they occur, and give practical advice on how to avoid them.
❌ Mistake No. 1: Incorrect dimensioning of the buttonhole openings
The most widespread and critical error is inaccurate marking of the hinge locations. If the hinge location is incorrectly marked, the doors may hang nervously, close poorly or not close at all.
✅ Yak unniknuti:
- Always use a tape measure, marker or a special template to make the markings.
- Observe the standard distance from the edge of the façade to the hinge cup (usually 21-22 mm).
- The distance from the upper and lower edge of the facade to the center of the hinge is often about 80-120 mm.
Remember: a good layout is a guarantee of further usability of furniture.
❌ Mistake #2: Incorrect drilling depth of openings
Inadequate depth of the opening for the hinge cup (too deep or not enough) can cause poor fit of the hinge to the facade or even damage to it.
✅ Yak unniknuti:
- Use a special Forstner drill bit with a diameter of 35 mm.
- The standard drilling depth for furniture hinges is 11-13 mm.
- Use the locking ring or the mark on the drill bit to precisely control the depth.
❌ Mistake #3: Use of inadequate or inappropriate fasteners
The choice of weak screws or inadequate fasteners causes the hinges to loosen quickly and, as a result, the doors to sag.
✅ Yak unniknuti:
- Use quality furniture screws of 3.5×16 mm or 4×16 mm.
- Always drill openings with a smaller diameter (2-3 mm) beforehand to prevent damage to the facade.
- Make sure that the screws are driven in briskly, but without excessive force, so as not to break the façade material.
❌ Mistake #4: Insufficient number of zavis for important facades
One of the most widespread errors is the installation of a small number of latches on important doors. This leads to a rapid sagging of the door and wear of the hinge mechanism.
✅ Yak unniknuti:
- For lightweight facades (up to 5 kg) two bolts are sufficient.
- For facades of 5-10 kg, it is better to use three hinges.
- For important facades (more than 10 kg, e.g. made of solid wood or timber) it is recommended to install three to four bolts, evenly distributing them in height.
❌ Mistake #5: Ignoring the regulation stage after installation
Even correctly installed hinges may require additional adjustment. Many newcomers do not follow this step, as a result of which the doors hang crookedly, are difficult to close or have unnecessary gaps.
✅ Yak unniknuti:
- After installation, it is imperative that the façade is precisely adjusted.
- Adjustment is carried out by three screws: vertically (height), horizontally (depth of fit) and right to left (gap width).
- Carry out the regulation step by step, checking the result after each action.
❌ Mistake #6: Incorrect selection of the type of curtain walling for a particular façade
There are different types of closures: overhead, overhead, inlay and hinges with a specific opening angle. Incorrect choice of the type of door will result in the facades not fitting correctly or not being installed at all.
✅ Yak unniknuti:
- Before purchasing, always clearly identify which type of façade you have (overlay, inlay or overlay).
- Pay attention to the hinge opening angle (for kitchens it is optimal 95-110° or more, for special furniture other angles are possible).
❌ Mistake #7: Lack of attention to the quality of the curtains themselves
In an attempt to save money, many people choose cheap hinges from unknown manufacturers. Such hinges wear out quickly, break or lose their characteristics (for example, the door closer mechanism malfunctions).
✅ Yak unniknuti:
- Choose curtains from trusted brands (Blum, Hettich, Grass, Häfele, GTV) that guarantee durability and reliability.
- Make sure that the doors have an anti-corrosion coating and a good quality soft-closing mechanism (door closer).
📌 General recommendations to avoid mistakes when installing furniture curtains:
- Always double-check measurements and markings before drilling.
- Do not rush, do the installation carefully and one by one.
- Use quality tools and fasteners.
- Do not skip the final stage of regulation.
🛠️ Wisnovok
Correct installation of furniture curtains allows you to avoid most of the problems with the operation of furniture. Remember that even small mistakes at the initial stages can cause significant problems in the future. Use the recommendations given above, and your furniture will serve for a long time, reliably and comfortably.
